API EXPLORATION AND PRODUCTION STANDARDS

exploracion y produccion de petroleoAPI MPMS 1
Manual of Petroleum Measurement Standards Chapter 1 – VocabularyAPI MPMS 1 SPANISH
Manual de Estándares de Medición de Petróleo Capítulo 1 Vocabulario-

API MPMS 10.1
Manual of Petroleum Measurement Standards Chapter 10 – Sediment and Water Section 1 – Standard Test Method for Sediment in Crude Oils and Fuel Oils by the Extraction Method

API MPMS 10.2
Manual of Petroleum Measurement Standards Chapter 10 – Sediment and Water Section 2 – Standard Test Method for Water in Crude Oil by Distillation

API MPMS 10.3
Manual of Petroleum Measurement Standards Chapter 10-Sediment and Water Section 3-Standard Test Method for Water and Sediment in Crude Oil by the Centrifuge Method (Laboratory Procedure)

API MPMS 10.4
Manual of Petroleum Measurement Standards Chapter 10 – Sediment and Water Section 4 – Determination of Water and/or Sediment in Crude Oil by the Centrifuge Method (Field Procedure)

API MPMS 10.7
Manual of Petroleum Measurement Standards Chapter 10 – Sediment and Water Section 7 – Standard Test Method for Water in Crude Oils by Karl Fischer Titration

API MPMS 10.8
Manual of Petroleum Measurement Standards Chapter 10 – Sediment and Water Section 8 – Standard Test Method for Sediment in Crude Oil by Membrane Filtration

API MPMS 10.9
Manual of Petroleum Measurement Standards Chapter 10 Sediment and Water Section 9 Standard Test Method for Water in Crude Oils by Coulometric Karl Fischer Titration

API MPMS 11.1
Manual of Petroleum Measurement Standards Chapter 11-Physical Properties Data Section 1-Temperature and Pressure Volume Correction Factors for Generalized Crude Oils Refined Products and Lubricating Oils

API MPMS 11.2
Manual of Petroleum Measurement Standards Chapter 11.2.1 and 11.2.1M – Compressibility Factors for Hydrocarbons: 0-90 Degrees API Gravity and 638-1074 Kilograms per Cubic Metre Ranges Chapter 11.2.3 and 11.2.3M – Water

API MPMS 11.2.2
Manual of Petroleum Measurement Standards Chapter 11.2.2-Compressibility Factors for Hydrocarbons: 0.350-0.637 Relative Density (60°F/60°F) and -50°F to 140°F Metering Temperature

API MPMS 11.2.2
Manual of Petroleum Measurement Standards Chapter 11 – Physical Properties Data Addendum to Section 2 Part 2 – Compressibility Factors for Hydrocarbons Correlation of Vapor Pressure for Commercial Natural Gas Liquid

API MPMS 11.2.2M
Manual of Petroleum Measurement Standards Chapter 11.2.2M – Compressibility Factors for Hydrocarbons: 350-637 Kilograms per Cubic Metre Density (15 Degrees C) and -46 Degrees C to 60 Degrees C Metering Temperature

API MPMS 11.2.4
Manual of Petroleum Measurement Standards Chapter 11-Physical Properties Data Section 2 Part 4-Temperature Correction for the Volume of NGL and LPG Tables 23E 24E 53E 54E 59E and 60E

API MPMS 11.2.5
Manual of Petroleum Measurement Standards Chapter 11-Physical Properties Data Section 2 Part 5-A Simplified Vapor Pressure Correlation for Commercial NGLs

API MPMS 11.3.2.1
Manual of Petroleum Measurement Standards Chapter 11.3.2.1-Ethylene Density

API MPMS 11.3.3.2
Manual of Petroleum Measurement Standards Chapter 11.3.3.2 – Propylene Compressibility Tables-Includes Access to Additional Content

API MPMS 11.4.1
Manual of Petroleum Measurement Standards Chapter 11-Physical Properties Data Section 4-Properties of Reference Materials Part 1-Density of Water and Water Volumetric Correction Factors for Water Calibration of

API MPMS 11.5
Density/Weight/Volume Intraconversion-First Edition; Includes Access to Additional Content

API MPMS 12.1.1
Manual of Petroleum Measurement Standards Chapter 12-Calculation of Petroleum Quantities Section 1-Calculation of Static Petroleum Quantities Part 1-Upright Cylindrical Tanks and Marine Vessels

API MPMS 12.1.1
Manual of Petroleum Measurement Standards Chapter 12-Calculation of Petroleum Quantities

API MPMS 12.1.1
Manual de Estándares de Medición de Petróleo Capítulo 12-Cálculo de Cantidades de Petróleo Sección 1-Cálculo de Cantidades de Petróleo Estático Parte 1-Tanques Cilíndricos Verticales y Buques

API MPMS 12.1.1
Manual de Estándares de Medición de Petróleo Capitulo 12-Cálculo de Cantidades de Petróleo

API MPMS 12.1.2
Manual of Petroleum Measurement Standards Chapter 12 – Calculation of Petroleum Quantities Section 1 – Calculation of Static Petroleum Quantities Part 2 – Calculation Procedures for Tank Cars

API MPMS 12.1.2
Manual of Petroleum Measurement Standards Chapter 12-Calculation of Petroleum Quantities

API MPMS 12.2.1
Manual of Petroleum Measurement Standards Chapter 12 – Calculation of Petroleum Quantities Section 2 – Calculation of Petroleum Quantities Using Dynamic Measurement Methods and Volumetric Correction Factors

API MPMS 12.2.1
Manual of Petroleum Measurement Standards Chapter 12-Calculation of Petroleum Quantities

API MPMS 12.2.1
Manual of Petroleum Measurement Standards Chapter 12 – Calculation of Petroleum Quantities Section 2 – Calculation of Petroleum Quantities Using Dynamic Measurement Methods and Volumetric Correction Factors

API MPMS 12.2.2
Manual of Petroleum Measurement Standards Chapter 12 – Calculation of Petroleum Quantities Section 2 – Calculation of Petroleum Quantities Using Dynamic Measurement Methods and Volumetric Correction Factors

API MPMS 12.2.2
Manual of Petroleum Measurement Standards Chapter 12-Calculation of Petroleum Quantities

API MPMS 12.2.3
Calculation of Petroleum Quantities – Section 2 – Calculation of Petroleum Quantities Using Dynamic Measurement Methods and Volumetric Correction Factors – Part 3 – Proving Reports

API MPMS 12.2.3
Manual of Petroleum Measurement Standards Chapter 12-Calculation of Petroleum Quantities

API MPMS 12.2.4
Manual of Petroleum Measurement Standards Chapter 12 – Calculation of Petroleum Quantities Section 2 – Calculation of Petroleum Quantities Using Dynamic Measurement Methods and Volumetric Correction Factors

API MPMS 12.2.4
Manual of Petroleum Measurement Standards Chapter 12-Calculation of Petroleum Quantities

API MPMS 12.2.4
Manual of Petroleum Measurement Standards Chapter 12 – Calculation of Petroleum Quantities Section 2 – Calculation of Petroleum Quantities Using Dynamic Measurement Methods and Volumetric Correction Factors

API MPMS 12.2.5
Manual of Petroleum Measurement Standards Chapter 12 – Calculation of Petroleum Quantities Section 2 – Calculation of Petroleum Quantities Using Dynamic Measurement Methods and Volumetric Correction Factors

API MPMS 12.2.5
Manual of Petroleum Measurement Standards Chapter 12-Calculation of Petroleum Quantities

API MPMS 12.2.5
Manual of Petroleum Measurement Standards Chapter 12 – Calculation of Petroleum Quantities Section 2 – Calculation of Petroleum Quantities Using Dynamic Measurement Methods and Volumetric Correction Factors

API MPMS 12.3
Manual of Petroleum Measurement Standards Chapter 12 – Calculation of Petroleum Quantities Section 3 – Volumetric Shrinkage Resulting from Blending Light Hydrocarbons with Crude Oils

API MPMS 12.3
Manual of Petroleum Measurement Standards Chapter 12-Calculation of Petroleum Quantities

API MPMS 14.1
Manual of Petroleum Measurement Standards Chapter 14 – Natural Gas Fluids Measurement Section 1 – Collecting and Handling of Natural Gas Samples for Custody Transfer

API MPMS 14.10
Manual of Petroleum Measurement Standards Chapter 14 – Natural Gas Fluids Measurement Section 10-Measurement of Flow to Flares

API MPMS 14.3.1
Manual of Petroleum Measurement Standards Chapter 14 – Natural Gas Fluids Measurement Section 3 – Concentric Square-Edged Orifice Meters Part 1 – General Equations and Uncertainty Guidelines

API MPMS 14.3.2
Manual of Petroleum Measurement Standards Chapter 14Natural Gas Fluids Measurement Section 3 Concentric Square-Edged Orifice Meters Part 2Specification and Installation Requirements

API MPMS 14.3.3
Manual of Petroleum Measurement Standards Chapter 14 – Natural Gas Fluids Measurement Section 3 – Concentric Square-Edged Orifice Meters Part 3 – Natural Gas Applications

API MPMS 14.3.4
Manual of Petroleum Measurement Standards Chapter 14-Natural Gas Fluids Measurement Sect ion 3-Concent ric Square-Edged Orifice Meters Part 4-Background Development Implementation Procedures and Subroutine Document

API MPMS 14.4
Manual of Petroleum Measurement Standards Chapter 14 – Natural Gas Fluids Measurement Section 4 – Converting Mass of Natural Gas Liquids and Vapors to Equivalent Liquid Volumes

API MPMS 14.5
Calculation of Gross Heating Value Relative Density Compressibility and Theoretical Hydrocarbon Liquid Content for Natural Gas Mixtures for Custody Transfer

API MPMS 14.6
Manual of Petroleum Measurement Standards Chapter 14 – Natural Gas Fluids Measurement Section 6 – Continuous Density Measurement

API MPMS 14.7
Mass Measurement of Natural Gas Liquids

API MPMS 14.8
Manual of Petroleum Measurement Standards Chapter 14 – Natural Gas Fluids Measurement Section 8 – Liquefied Petroleum Gas Measurement

API MPMS 17.1
Manual of Petroleum Measurement Standards Chapter 17-Marine Measurement Section 1-Guidelines for Marine Cargo Inspection

API MPMS 17.1 Manual de Estándares de Medición de Petróleo Capítulo 17 – Mediciones Mar?timas Sección 1 – Guías Para la Inspección de Cargas Maritimas

API MPMS 17.11
Manual of Petroleum Measurement Standards Chapter 17.11 EI Hydrocarbon Management HM 52 Measurement and sampling of cargoes on board tank vessels using closed and restricted equipment

API MPMS 17.12
Procedure for bulk liquid chemical cargo inspection by cargo inspectors

API MPMS 17.2
Manual de Normas de Mediciones Petroleras Capitulo 17 – Mediciones Marinas Seccio`n – Medicio`n de cargas a bordo de buquetanques

API MPMS 17.4
Manual de Estándares de Medición del Petróleo Capítulo 17 Mediciones Marítimas Sección 4 Método para Cuantificación de Volúmenes Pequeños en Buques.

API MPMS 17.6
Manual de Estándares de Medición del Petróleo Capítulo 17Mediciones Marítimas Sección 6 Guías para Determinar el Llenado de Líneas Entre Buques y Tanques en Tierra

API MPMS 17.9
Manual de Estándares de Medición del Petróleo Capitulo 17-Mediciones Marítimas Sección 9-Factor de Experiencia del Buque (VEF) IP Hydrocarbon Management HM 49
API MPMS 18.1
Manual of Petroleum Measurement Standards Chapter 18 – Custody Transfer Section 1 – Measurement Procedures for Crude Oil Gathered From Small Tanks by Truck

API MPMS 19.1
Manual of Petroleum Measurement Standards Chapter 19 – Evaporative Loss Measurement Section 1 – Evaporative Loss from Fixed-Roof Tanks-Third Edition: Incorporates Addendum: 8/2008

API MPMS 19.1A
Evaporation Loss from Low-Pressure Tanks

API MPMS 19.1D
Documentation File for API Manual of Petroleum Measurement Standards Chapter 19.1 – Evaporative Loss from Fixed Roof Tanks

API MPMS 19.2
Manual of Petroleum Measurement Standards Chapter 19 – Evaporative Loss Measurement Section 2 – Evaporative Loss from Floating-Roof Tanks

API MPMS 19.3 PART A
Manual of Petroleum Measurement Standards Chapter 19.3-Evaporative Loss Measurement Part A-Wind Tunnel Test Method for the Measurement of Deck-Fitting Loss Factors for External Floating-Roof Tanks

API MPMS 19.3 PART B
Manual of Petroleum Measurement Standards Chapter 19.3 – Evaporative Loss Measurement Part B – Air Concentration Test Method – Rim-Seal Loss Factors for Floating-Roof Tanks
API MPMS 19.3 PART C
Manual of Petroleum Measurement Standards Chapter 19.3 – Evaporative Loss Measurement Part C – Weight Loss Test Method for the Measurement of Rim-Seal Loss Factors for Internal Floating-Roof Tanks
API MPMS 19.3 PART D
Manual of Petroleum Measurement Standards Chapter 19.3 – Evaporative Loss Measurement Part D – Fugitive Emission Test Method for the Measurement of Deck-Seam Loss Factors for Internal Floating-Roof Tanks

API MPMS 19.3 PART E
Manual of Petroleum Measurement Standards Chapter 19.3 – Evaporative Loss Measurement Part E – Weight Loss Test Method for the Measurement of Deck-Fitting Loss Factors for Internal Floating-Roof Tanks

API MPMS 19.3 PART H
Manual of Petroleum Measurement Standards Chapter 19.3 – Evaporative Loss Measurement Part H – Tank Seals and Fittings Certification – Administration
API MPMS 19.4
Manual of Petroleum Measurement Standards Chapter 19.4 – Recommended Practice for Speciation of Evaporative Losses

API MPMS 19.4 ERTA
Manual of Petroleum Measurement Standards Chapter 19.4 – Recommended Practice for Speciation of Evaporative Losses

API MPMS 2.2A
Manual of Petroleum Measurement Standard Chapter 2 – Tank Calibration Section 2A – Measurement and Calibration of Upright Cylindrical Tanks by the Manual Tank Strapping Method

API MPMS 2.2B
Manual of Petroleum Measurement Standards Chapter 2 – Tank Calibration Section 2B – Calibration of Upright Cylindrical Tanks Using the Optical Reference Line Method

API MPMS 2.2C
Manual of Petroleum Measurement Standards Chapter 2 – Tank Calibration Section 2C – Calibration of Upright Cylindrical Tanks Using the Optical-Triangulation Method

API MPMS 2.2D
Manual of Petroleum Measurement Standards Chapter 2 – Tank Calibration Section 2D – Calibration of Upright Cylindrical Tanks Using the Internal Electro-optical Distance-ranging Method

API MPMS 2.2E
Petroleum and Liquid Petroleum Products – Calibration of Horizontal Cylindrical Tanks – Part 1: Manual Methods-First Edition; ISO 12917-1 Adoption

API MPMS 2.2E ERTA
Petroleum and Liquid Petroleum Products – Calibration of Horizontal Cylindrical Tanks – Part 1: Manual Methods-First Edition; ISO 12917-1 Adoption

API MPMS 20.1
Manual of Petroleum Measurement Standards Chapter 20 – Allocation Measurement Section 1 – Allocation Measurement

API MPMS 21.1
Manual of Petroleum Measurement Standards Chapter 21 – Flow Measurement Using Electronic Metering Systems Section 1 – Electronic Gas Measurement

API MPMS 21.2
Manual of Petroleum Measurement Standards Chapter 21 – Flow Measurement Using Electronic Metering Systems Section 2 – Flow Measurement using Electronic Metering Systems Inferred Mass

API MPMS 22.1
General Guidelines for Developing Testing Protocols for Devices Used in the Measurement of Hydrocarbon Fluids

API MPMS 22.2
Manual of Petroleum Measurement Standards Chapter 22Testing Protocol Section 2Differential Pressure Flow Measurement Devices

API MPMS 3.1A
Manual of Petroleum Measurement Standards Chapter 3 – Tank Gauging Section 1A – Standard Practice for the Manual Gauging of Petroleum and Petroleum Products

API MPMS 3.1A
Manual de Estándares de Medición de Petróleo Capítulo 3 – Medición del Tanque Sección 1A – Procedimiento Estándar para la Medición Manual de Petróleo y Productos del Petróleo

API MPMS 3.1B
Manual of Petroleum Measurement Standards Chapter 3 – Tank Gauging Section 1B – Standard Practice for Level Measurement of Liquid Hydrocarbons in Stationary Tanks by Automatic Tank Gauging

API MPMS 3.6
Manual of Petroleum Measurement Standards Chapter 3 – Tank Gauging; Section 6 – Meaurement of Liquid Hydrocarbons by Hybrid Tank Measurement Systems

API MPMS 4.1
Manual of Petroleum Measurement Standards Chapter 4 – Proving Systems Section 1 – Introduction

API MPMS 4.2
Manual of Petroleum Measurement Standards Chapter 4 – Proving Systems Section 2 – Displacement Provers

API MPMS 4.4
Manual of Petroleum Measurement Standards Chapter 4 – Proving Systems Section 4 – Tank Provers

API MPMS 4.5
Manual of Petroleum Measurement Standards Chapter 4 – Proving Systems Section 5 – Master-Meter Provers

API MPMS 4.6
Manual of Petroleum Measurement Standards Chapter 4 – Proving Systems Section 6 – Pulse Interpolation

API MPMS 4.7
Manual of Petroleum Measurement Standards Chapter 4 – Proving Systems Section 7 – Field – Standard Test Measures

API MPMS 4.8
Manual of Petroleum Measurement Standards Chapter 4 – Proving Systems Section 8 – Operation of Proving Systems

API MPMS 4.9.1
Manual of Petroleum Measurement Standards Chapter 4Proving Systems Section 9Methods of Calibration for Displacement and 1Introduction to the Determination of the Volume of Displacement and Tank Provers

API MPMS 4.9.2
Manual of Petroleum Measurement Standards Chapter 4Proving Systems Section 9Methods of Calibration for Displacement and Volumetric Tank Provers Part 2Determination of the Volume of Displacement and Tank

API MPMS 4.9.3
Manual of Petroleum Measurement Standards Chapter 4-Proving Systems Section 9-Methods of Calibration for Displacement and Volumetric Tank Provers Part 3-Determination of the Volume of Displacement

API MPMS 5.1
Manual of Petroleum Measurement Standards Chapter 5 – Metering Section 1 – General Considerations for Measurement by Meters

API MPMS 5.2
Manual of Petroleum Measurement Standards Chapter 5 – Metering Section 2 – Measurement of Liquid Hydrocarbons by Displacement Meters

API MPMS 5.3
Manual of Petroleum Measurement Standards Chapter 5 – Metering Section 3 – Measurement of Liquid Hydrocarbons by Turbine Meters

API MPMS 5.4
Manual of Petroleum Measurement Standards Chapter 5 – Metering Section 4 – Accessory Equipment for Liquid Meters

API MPMS 5.5
Manual of Petroleum Measurement Standards Chapter 5 – Metering Section 5 – Fidelity and Security of Flow Measurement Pulsed-Data Transmission Systems

API MPMS 5.8
Manual of Petroluem Measurement Standards Chapter 5 – Metering – Section 8 – Measurement of Liquid Hydrocarbons by Ultrasonic Flow Meters Using Transit Time Technology

API MPMS 6.1
Manual of Petroleum Measurement Standards Chapter 6 – Metering Assemblies Section 1 – Lease Automatic Custody Transfer (LACT) Systems

API MPMS 6.5
Manual of Petroleum Measurement Standards Chapter 6 – Metering Assemblies Section 5 – Metering Systems for Loading and Unloading Marine Bulk Carriers

API MPMS 6.7
Manual of Petroleum Measurement Standards Chapter 6 – Metering Assemblies Section 7 – Metering Viscous Hydrocarbons

API MPMS 8.1
Manual of Petroleum Measurement Standards Chapter 8 – Sampling Section 1 – Standard Practice for Manual Sampling of Petroleum and Petroleum Products

API MPMS 8.1
Manual de Estándares de Medición de Petróleo Capítulo 8-Muestreo Sección 1-Procedimiento Estándar para Muestreo Manual de Petróleo y Productos de Petróleo

API MPMS 8.2
Manual of Petroleum Measurement Standards Chapter 8 – Sampling Section 2 – Standard Practice for Automatic Sampling of Liquid Petroleum and Petroleum Products-Second Edition

API MPMS 8.3
Manual of Petroleum Measurement Standards Chapter 8 – Sampling Section 3 – Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products

API MPMS 8.4
Manual of Petroleum Measurement Standards Chapter 8 – Sampling Section 4 – Standard Practice for Sampling and Handling of Fuels for Volatility Measurement

API MPMS 9.1
Manual of Petroleum Measurement Standards Chapter 9 – Density Determination Section 1 – Standard Test Method for Density Relative Density (Specific Gravity) or API Gravity of Crude Petroleum and Liquid Petroleum

API MPMS 9.3
Manual of Petroleum Measurement Standards Chapter 9 – Density Determination Section 3 – Standard Test Method for Density Relative Density and API Gravity of Crude Petroleum and Liquid Petroleum Products by Thermohy

API PUBL 2558
Wind Tunnel Testing of External Floating-Roof Storage Tanks

API PUBL 4698
Review of Technologies to Measure the Oil and Grease Content of Produced Water from Offshore Oil and Gas Production Operations

API RP 2556
Correction Gauge Tables For Incrustation

API STD 2555
Method for Liquid Calibration of Tanks

API TR 2567
Evaporative Loss from Storage Tank Floating Roof Landings

API MPMS 17.1

Sé el primero en comentar

Dejar una contestacion

Tu dirección de correo electrónico no será publicada.


*